Cartridge Maintenance/ Repair Guide

Cartridge Maintenance/

Repair Guide

Introduction

Thank you for choosing Chicago Faucets! All Chicago Faucets products are carefully assembled and tested to

insure the highest quality in the plumbing industry. We are proud to offer you a product that will provide years of

dependable, reliable service.

The Maintenance and Repair Guide is intended to provide you, as a customer, with step-by-step procedures for

replacing or renewing our most popular cartridges. These procedures are limited to minor problems that are the

result of normal wear and not intended to cover repairs that are the result of damage caused by abuse or vandalism.

Ceramic Cartridge Replacement 3

Renewing Quaturn

™

and Slow Compression Operating Cartridges 4

Renewing KLO-SELF

™

Cartridges 5

Timing Adjustment of MVP

™

Metering Valves 6

Renewing MVP Metering Valves 7

NAIAD

™

Push Button Adjustment 8

Renewing NAIAD Cartridges 9

NAIAD Oscillating Cartridge Adjustment 10

Repair NAIAD Oscillating and Dashpot Cartridges 11

Replacement Cartridge Model Numbers 12

ECAST

Cartridges 13

Repair Kits 14 - 15

Installation of Ceramic Cartridge

Step 1 Push each cartridge into valve

body until it seats. Add cap nuts and

hand tighten. Add handles.

Step 2 Rotate RIGHT handle (and

cartridge) counter clockwise to the

desired closed position.

Step 3 Using handle to maintain stem

position, fully tighten right cap nut to 20

to 27 ft. lb. torque.

Step 4 Move LEFT handle (without

moving cartridge) to the open position

and fully tighten right cap nut to 20 to

27 ft. lb. torque. Return handle to closed

position.

Note: No replacement parts for ceramic cartridges,

sold only as complete assembly.

*For ceramic cartridges with integral check valves, see page 12.

Ensure cartridges are in the closed

position before installing into valve body.

Cartridges feature color-coded seats. Blue

seat on cold cartridge, red seat on hot

cartridge.

Color-coded seat

Ceramic Operating Cartridges

Short Stem*

No. 1-100XKJKNF

Left Hand Cartridge

No. 1-099XKJKNF

Right Hand Cartridge

Long Stem*

No. 377-XKLHJKNF

Left Hand Cartridge

No. 377-XKRHJKNF

Right Hand Cartridge

Stem Identification

Renewing “XT” Quaturn

™

or Slow Compression Cartridges

STEP 1 - Turn off water at stop

or main valve. Remove handle

assembly and with flat face

wrench, remove cap nut (A).

STEP 2 - Remove cartridge from

faucet. Flush out any rust or chips

that may be in body. DO NOT

use file or abrasives to clean out

body.

STEP 3 - Unscrew stem nut (K) at

the bottom of the cartridge with

a flat wrench using a handle as

lever to assist removal.

STEP 4 - Turn sleeve (D) off

stem (C) by holding handle and

turn sleeve by hand. As sleeve

is removed from stem, seat (F)

O-Ring (G) seat washer (H) retain-

er (I) and washer (J) will be forced

off the stem.

STEP 5 - Reassemble sleeve (D)

on lightly lubricated stem (C).

With new parts add seat (F)

O-Ring (G) seat washer (H) retain-

er (I) and washer (J) on stem (C)

and screw nut tightly on stem.

STEP 6 - Reposition washer and

O-Ring (B) on stem (C) add to

sleeve (D). Replace cartridge in

faucet.

STEP 7 - Replace Cap Nut (A)

and partially tighten. Replace

handle and rotate cartridge in

the direction of closing until the

cartridge is in the desired position

for convenient operation. Remove

handle. Lock cartridge in place by

securely tightening Cap Nut (A)

to 20 - 27 ft. lbs torque.

STEP 8 - Turn water on at main

valve or stop. Remove aerator.

Turn faucet on to “full” allowing

sediment to flush from lines and

replace aerator cartridge.

“XT” TYPE CARTRIDGES

PARTS LIST - Those parts listed in the “Description” column below that are marked with an asterisk (*) are parts that are

recommended for replacement when renewing these operating cartridges. Other parts not marked may require replacement

depending on the amount of wear they have received and their condition when examined. Most of the parts listed below

are also available in multi-packs (box lots). See chicagofaucets.com or call Chicago Faucets Customer Service for more

information. Note: items without a listed part number are not available to purchase separately.

Quaturn Cartridges Slow Compression Cartridges

Exposed Cap Concealed Cap Exposed Cap Concealed Cap

Description

1-009XTJKABNF 1-100XTJKABNF 377-XTRHJKABNF 377-XTLHJKABNF 217-XTLHJKABNF 217-XTRHJKABNF 274-XTLHJKABNF 274-XTRHJKABNF

A. Cap

1-214JKCP

274-004JKRBF 274-004JKRBF 1-214JKCP 1-214JKCP 274-004JKRBF 274-004JKRBF

B. Packing Assembly

* 93-131JKABNF 93-131JKABNF 93-131JKABNF 93-131JKABNF 93-131JKABNF 93-131JKABNF 93-131JKABNF 93-131JKABNF

C. Stem Assy. w/ O-Ring – – – – – – – –

D. Sleeve – – – – – – – –

E. O-Ring 2-043JKABNF 2-043JKABNF 2-043JKABNF 2-043JKABNF 2-043JKABNF 2-043JKABNF 2-043JKABNF 2-043JKABNF

F. Seat

* 1-327JKABNF 1-327JKABNF 1-327JKABNF 1-327JKABNF 1-327JKABNF 1-327JKABNF 1-327JKABNF 1-327JKABNF

G. O-Ring 1-328JKABNF 1-328JKABNF 1-328JKABNF 1-328JKABNF 1-328JKABNF 1-328JKABNF 1-328JKABNF 1-328JKABNF

H. Seat Washer

* 1-021JKABNF 1-021JKABNF 1-021JKABNF 1-021JKABNF 1-021JKABNF 1-021JKABNF 1-021JKABNF 1-021JKABNF

I. Retainer 1-022JKABNF 1-022JKABNF 1-022JKABNF 1-022JKABNF 1-022JKABNF 1-022JKABNF 1-022JKABNF 1-022JKABNF

J. Washer 1-031JKABNF 1-031JKABNF 1-031JKABNF 1-031JKABNF 1-031JKABNF 1-031JKABNF 1-031JKABNF 1-031JKABNF

K. Nut 333-097JKABNF 333-097JKABNF 333-097JKABNF 333-097JKABNF 333-097JKABNF 333-097JKABNF 333-097JKABNF 333-097JKABNF

Renewing KLO-SELF Cartridges

STEP 1 - Turn off water at stop

or main valve. Remove handle,

loosen cap nut (A) with flat faced

wrench and remove upper parts

of cartridge consisting of stem

(C), bonnet (B) and spring (D).

STEP 2 - With pliers, grab the car-

tridge stem and pull up, removing

it from the body.

STEP 3 - Holding the flat portion of

plunger (E) remove stem nut (P).

After stem nut is removed, remove

washer (O), retainer (N) seat

washer (M) and Monel seat (L) by

tapping bottom of plunger until

parts are loosened. Now, remove

O-Rings (H), leather

packing (I), gland (G) and spring

(F) from sleeve (K).

STEP 4 - To reassemble, clean

any lime or foreign matter that

may have built-up on parts.

Lubricate plunger surface (E) and

place spring (F) and gland (G) on

plunger. Replace the (2) O-Rings

(H) making sure that the leather

packing is placed between them.

Slide O-Rings and leather packing

on the plunger. Lubricate O-Rings

and leather packing with a light

grease before the plunger is

inserted into the sleeve (K).

STEP 5 - Replace Monel seat (L),

seat washer (M), retainer (N), cup

washer (O), and tighten nut (P)

securely.

STEP 6 - Replace O-Ring (J) with

new O-Ring, inserting into groove

on the sleeve (K). Lubricate outside

of O-Ring, stem (C) and inside of

bonnet (B). Lubricate spring (D)

and insert into stem. Assemble

upper parts of cartridge (B,C,D)

and tighten nut (A) to faucet

body sufficiently (25 - 32 ft. lbs.) to

insure that metal to metal contact

of lower seat (L) in faucet body.

Bonnet and sleeve must also make

metal to metal contact. Replace

handle.

STEP 7 - Turn water on at stop

or main valve. Remove aerator.

Turn faucet on to “full” allowing

sediment to flush from lines and

replace aerator cartridge.

823-004JKCP - Nut

823-001JKABNF - Plunger

823-010JKNF - Spring

319-140JKABNF - “O” Rings

823-015JKABNF - “O” Ring

244-006JKABNF - Washer

1-031JKABNF - Washer

585-001JKBNF - Stem

826-101JKRCF - Bonnet

711-007JKRBF - Gland

319-035JKABNF - Leather Packing

1-027JKABNF - Seat

1-022JKABNF - Retainer

333-97JKABNF - Nut

823-013JKNF - Spring

826-XJKABNF Parts Overview

MVP

™

Metering Valve

665-PSHJKCP - Push handle

665-505JKNF - 3/32˝ hex socket wrench

665-309KJKNF - Red and

blue index buttons

665-116JKNF - Hex socket screw

665-015JKRBF - Spring retainer

665-105JKABNPF - Stem

668-013JKNF - Return spring

665-118JKNF - Adjustment nut

665-190KJKABNF - Actuator

assembly

671-XJKABNF - Cartridge assembly

Cap assembly

“O” Ring

Retainer ring

665-011JKABNF - Cap sealing washer

Valve sleeve

667-107JKABNF - “O” Ring

Poppet/seat assembly

667-402JKABNF - Large filter

667-202JKABNF - Filter for use with non-dashpot bodies

Timing Adjustment on an MVP Metering Cartridge

1 With handle in place, purge cartridge of air by pushing completely down 4-8 times rapidly,

then check timing cycle.

2 Remove handle with a 3/32 allen wrench.

3 Use a standard pair of pliers (other tools may damage the adjustment nut) to change height

of adjustment nut by 1/4 turn only. Turn adjustment nut clockwise to increase time.

4 Replace handle and time flow. NOTE: TIMING MUST BE CHECKED WITH HANDLE IN PLACE

5 If more adjustment is needed, follow steps 3 and 4 until timing is right.

6 Attach handle and tighten screw. Press index button into handle opening.

Adjustment

Nut

Index

button

Set

screw

Typical

Body

with red and blue

index buttons

and set screw

665-007JKABNF - (2) “E” ring retainers

Renewing MVP

™

Metering Valve

Step 1 Remove color coded index button from

handle with small, flathead screwdriver.

Step 2 Insert 3/32" allen wrench in handle

hole, loosen allen screw and remove handle.

Step 3 To adjust the flow cycle of the

MVP valve, turn the adjustment nut clockwise

to increase the duration of the flow cycle and

counter clockwise to decrease the flow cycle.

* After adjustment nut has been repositioned,

replace handle, push down and test flow

cycle.**

See page 6 for additional timing adjustment.

Step 4 If MVP cartridge is to be replaced,

TURN OFF WATER SUPPLY BEFORE

PROCEEDING. Using a wrench, remove

actuator assembly.

Step 5 Grasp cartridge valve top with

needle-nose pliers, remove MVP cartridge

from valve body. Be careful not to bend pin.

Remove filter screen from inside of body with

finger tip.

Step 6 Place new filter, screen and MVP

cartridge in valve body.

Step 7 and 8 Replace cap sealing washer and actuator assembly. (Adjust flow cycle as described in

#3.) Do not over tighten cap.

* While the adjustment nut can be hand adjusted, you may have to start the

adjustment by using a wrench or pliers. It is important to grip the adjustment

nut loosely so as not to deform or damage the nut.

Step 9 Replace handle, tighten handle nut

with allen wrench and replace index button.

** To properly test the flow cycle, the

valve handle must be in place and

actuated.

Adjustment

NAIAD

™

333-X and 333-XSLO Push Button Cartridge

Timing Adjustment on a NAIAD Push Button Slo-Closing Cartridge

Timing can be changed by adjusting the nut located at the lower end of the dashpot.

Shorter running time = LOOSEN (counter clockwise)

Longer running time = TIGHTEN (clockwise)

Note: Do not over tighten adjustment nut as it may cause continual run-on of faucet.

333-044KJKABCP - Button Assembly (Hot)

333-144KJKABCP - Button Assembly (Cold)

333-244KJKABCP - Button Assembly (Push)

1-043JKABNF - Gasket

1-027JKABNF - Seat

333-026JKABRBF - Retainer

333-039JKABNF - Washer

333-097JKABNF - Nut

319-035JKABNF - Leather Washer

395-018JKNF - Spring

319-003JKCP - Bonnet Cap

Sleeve

244-006JKABNF - Seat Washer

333-040JKABNF - Cup

1-031JKABNF - Washer

333-075JKABNF - Dash Pot

319-012JKRBF - Washer

319-140JKABNF - “O” Rings

No. 333-X NAIAD is used for all No. 333 Basin faucets and all push button stops and contains a fast

closing dashpot. Note: 333-XSLO is the same as No. 333-X, but with an additional external timing

feature located on the button and a 333-073KJKNF adjustable slow closing dashpot.

No. 625-X NAIAD operating cartridge is used for all pedal valves. Except for the 625 and 628 on which

the 628X one hole sleeve operating cartridge is used.

An adjustable slow closing model is available for both the 625-X and 628-X, which includes the

333-073KJKNF dashpot and is designated by 625-XSLO and 628-XSLO.

Timing

Nut

Renewing NAIAD

™

Cartridges

STEP 1 - Turn off water at stop or main valve.

Loosen bonnet cap (F) with flat faced wrench

and remove operating cartridge from valve

body. Remove the dashpot (P) from the body.

STEP 2 - To disassemble cartridge, insert pin

through hole in sleeve (H) and stem (A) to keep

stem from turning while nut (O) is removed.

(Same procedure is followed when assembling

operating cartridge.)

STEP 3 - Remove washer (N), washer (M), cup

(L), retainer (K), washer (J) and seat (I) from stem.

If leakage is occurring through spout outlet,

replace seat (I) and seat washer (J). Replace cup

(L), washer (M) and washer (N) as necessary.

STEP 4 - If water leakage is occurring around

the button assembly, remove button and stem

assembly (A) from sleeve (H) and bonnet cap

(F). Clean stem thoroughly and lubricate top

half with grease. Remove O-Rings (E) and wash-

er (C and D) from cap (F). Replace the packing

arrangement on stem assembly (A) by sliding

washer (C) on stem and then leather washer

(D) between the two O-Rings (E) onto the stem.

Next slide cap (F) onto stem (A) and firmly slide

cap up the stem to allow spring (B) to seat

O-Rings and washers in cap (F).

STEP 5 - Reassemble lower portion of

cartridge by sliding sleeve (H), seat (I), washer

(J), retainer (K), cup (L), washers (M and N)

and nut (O) in the same manner as described

in Step 2. Lightly grease exterior of cup (L).

Tighten nut (O) securely on stem using pin

through sleeve (H) and button assembly (A)

to contain assembly while tightening. Remove

pin when complete. Reposition dash pot (P) on

cartridge.

STEP 6 - Replace gasket (G) before placing

cartridge in valve body. Be sure gasket (G)

is around sleeve (H) before tightening cap (F)

to valve body. Turn water on at stop or main

valve. Remove aerator. Turn faucet on to “full”

allowing sediment to flush from lines and

operating cartridge. Replace aerator.

STEP 7 - See page 8 for dashpot timing of

Slo-Closing cartridges.

NAIAD

™

335-XJKABNF Tip-Tap Cartridge

Part No. Description

333-073KJKABNF Dash Pot Assembly (Adjustable)

Repair Parts Kits

Timing Adjustment on a NAIAD Tip-Tap Slo-Closing Cartridge

We have two adjustments featured on the Tip-Tap Cartridge.

For dashpot adjustments follow step 1.

For handle adjustment follow steps 2-3.

1 By tightening or loosening the 333-052 nut on the lower end of the dashpot, timing adjustment

is made. (Tightening increases running time. It is suggested that the thickness of the felt washer be

approximately 1/16" to 3/32" thick after tightening. This will deliver approximately 6-10 seconds timing.

Loosening decreases running time.)

2 Raise up front of tilt-handle to expose screw B. (use #6 allen key)

3 Set screw B adjusted all the way in gives maximum running time. Adjust set screw B out

counter-clockwise for less running time.

Handle

Adjustment

Screw

Timing

Nut

319-035JKABNF - Leather Washer

244-006JKABNF - Washer

333-040JKABNF - M Cup

1-031JKABNF - Washer

333-027JKABNF - Washer

333-052JKABNF - Nut

333-028JKABRBF - Washer

319-012JKRBF - Washer

Sleeve

335-002KJKRBF - Stem

335-005JKCP - Bonnet

1-043JKABNF - Gasket

1-027JKABNF - Seat

333-026JKABRBF - Retainer

333-097JKABNF - Nut

333-039JKABNF - Washer

395-018JKNF - Spring

319-140JKABNF - O-Rings

333-073KJKABNF - Dash Pot Assembly

335-007KJKCP - Hot Push Tilt Handle

335-107KJKCP - Cold Push Tilt Handle

335-207KJKCP - Plain Push Tilt Handle

NOTE: See page 9 for disassembly and reassembly of cartridge when renewing components.

How to Repair a NAIAD

™

Cartridge with

Dashpot and Oscillating Handle

1. To uncover operating cartridges on 386-XSLO urinal valves with non-sag handles, unscrew bonnet (17) and remove entire

assembly (23), on self-closing stops as shown on diagram below. For 386-X, remove bonnet (24) and handle (19).

2. Shut-off water at main or supply valve if installed.

3. Either cartridge can now be removed from body by loosening cap (6) with a flat wrench and lifting entire cartridge from

body including the dashpot.

4. If leakage is occurring through spout outlet, insert 1/8" diameter pin or pin wrench through hole in stem and with crescent

wrench remove stem nut (15) and all parts up to and including (9) seat. Inspect seat washer (10) and replace if necessary,

next inspect seat (9) for nicks or water cutting and replace if necessary. If cup washer (12) has been sticking in dashpot,

replace also.

5. If cartridge has been leaking between oscillating lever and upper cap, remove stem assembly (1) and spring (2) from sleeve (8)

and cap (6) by taking out washer (3) from cap, take out packing arrangement which consists of (2) O-Rings (4) with leather

washer (5) between O-Rings. Grease stem lightly around packing area and put new O-Rings and packing on stem using same

arrangement as indicated, also lubricate O. D. of packing.

6. Place stem with spring, washer and packing properly assembled back into cap and sleeve. Now assemble lower cartridge

parts in proper relation and insert pin or pin wrench in stem hole again and tighten nut (15). Grease cup (12) with light grease

and place cartridge in dashpot.

7. We recommend removing and replacing (7) gasket before cartridge is placed in valve body. Place cartridge in body and lock

cartridge by tightening cap (6) securely, add oscillating lever bonnet sub-assembly to cartridge.

Item Part

No. No. Description

1 386-008KJKRBF Button and Stem Assembly

2 395-018JKNF Spring

3 319-012JKRBF Brass Washer

4 319-140JKABNF O-Ring

5 319-035JKABNF Leather Washer

6 618-001JKCP Cap Nut

7 1-043JKABNF Gasket

8 – Sleeve

9 1-027JKABNF Monel Seat

10 244-006JKABNF Rubber Seat Washer

11 333-026JKABRBF Retainer

12 333-040JKABNF Rubber Washer

13 333-039JKABNF Washer

14 1-031JKABNF Stem Washer

15 333-097JKABNF Stem Nut

16 333-073KJKABNF Slow Dashpot Assembly

17 333-075KJKABNF Slow Dashpot Assembly

18 386-010JKCP Bonnet

19 386-009JKCP Ball Handle

20 386-011JKCP Plunger

21 386-013JKNF Spring

22 386-014JKRBF Sleeve

23 386-010KJKCP Handle Assembly

24 386-005JKCP Bonnet

NOTE: Complete assembly of 386-XSLO

cartridge and 386-010K Oscillating Lever

Handle assembly for Urinal Valves.

NOTE: Complete assembly of 386-X unit and

Oscillating Lever and Bonnet for

Self-Closing Stops.

386-XSLO 386-X

Replacement Cartridges

Quaturn

™

Compression Cartridge

Opens and closes in just a 1/4 turn

Unique design closes with water pressure

Standard in all centerset and widespread faucets for sink and lavatory

ADA Compliant when used with lever or wing handles

Renewable parts available

Product No. Description

1-099-245JKABNF Exposed Cap, Short Stem, Right Hand Control-A-Flo

1-099STJKNF Steam Cartridge

1-099XTJKABNF Exposed Cap, Short Stem, Right Hand

1-099XTJKSPF Exposed Cap, Short Stem, Right Hand, Silver Plate Finish

1-099XTJKTPF Exposed Cap, Short Stem, Right Hand, Tin Plate Finish

1-100-245JKABNF Exposed Cap, Short Stem, Left Hand Control-A-Flo

1-100XTJKABNF Exposed Cap Short Stem, Left Hand

1-100XTJKSPF Exposed Cap, Short Stem, Left Hand, Silver Plate Finish

1-100XTJKSPF Exposed Cap, Short Stem, Left Hand, Tin Plate Finish

1105-XLHJKABNF Exposed Cap, Long Stem, Left Hand

1105-XRHJKABNF Exposed Cap, Long Stem, Right Hand

377-X245LHJKABNF Concealed Cap, Long Stem, Left Hand Control-A-Flo

377-X245RHJKABNF Concealed Cap, Long Stem, Right Hand Control-A-Flo

377-XTLHJKABNF Concealed Cap, Left Hand

377-XTRHJKABNF Concealed Cap, Right Hand

Ceramic

Cartridge

Positive 1/4 turn, eliminating handle travel

Available as a substitute for the Quaturn compression cartridge

ADA Compliant when used with lever or wing handles

Product No. Description

1-099XKCJKABNF Exposed Cap Short Stem with Integral Check Valve, Right Hand

1-099XKJKABNF Exposed Cap Short Stem, Right Hand

1-100XKCJKABNF Exposed Cap Short Stem with Integral Check Valve, Left Hand

1-100XKJKABNF Exposed Cap Short Stem, Left Hand

377-XKLHJKABNF Concealed Cap, Long Stem, Left Hand

377-XKRHJKABNF Concealed Cap, Long Stem, Right Hand

420-XJKABNF For 420 Series Faucets

430-XJKABNF For 430 Series Faucets

2300-XJKABNF For Marathon Single Control Kitchen and Lavatory Faucets

Slow Compression

Cartridge

For finer adjustment of water volume

Most common in laboratory fittings

Requires approximately one full turn to open and close completely

ADA Compliant when used with lever or wing handles

Metering

Self-Closing, Adjustable Cartridge

Close either upon release or within a 2-15 second cycle time

Helps reduce water usage in high traffic locations

Product No. Description

NAIAD

™

Cartridges

333-XPSHJKABNF Exposed Cap, Push Button, Immediate Closure

333-XCOLDJKABNF Exposed Cap, Cold Button, Immediate Closure

333-XHOTJKABNF Exposed Cap, Hot Button, Immediate Closure

333-XSLOCJKABNF Exposed Cap, Cold Button, Adjustable Cycle Time

333-XSLOPJKABNF Exposed Cap, Push Button, Adjustable Cycle Time

333-XSLOHOTJKABNF Exposed Cap, Hot Button, Adjustable Cycle Time

335-XJKABNF Exposed Cap “Tip-Tap” Cartridge, Adjustable Cycle Time

408-XPSHJKABNF Exposed Cap, Push Button, Adjustable Cycle Time

409-XJKABNF Exposed Cap “Tip-Tap” Cartridge, Adjustable Cycle Time

807-XPSHJKABNF Exposed Cap, Push Button, Adjustable Cycle Time

Pedal Box Cartridges

625-XJKABNF Pedal Box Cartridge, No Index, High Flow Characteristics

628-XJKABNF Pedal Box Cartridge, No Index, Low Flow Characteristics

625-XSLOJKABNF Pedal Box Cartridge, No Index, Slow Closing

628-XSLOJKABNF Pedal Box Cartridge, No Index, Slow Closing

628-XJKABTPF Pedal Box Cartridge, No Index, Slow Closing, Tin Plate Finish

MVP

™

Adjustable Timing Cartridges

665-190KJKABNF MVP Actuator Assembly

667-080KJKABNF MVP Actuator Assembly and MVP Valve with Filter Screen

668-100KJKABNF MVP Cartridge Rebuilding Kit

671-XJKABNF MVP Valve with Filter Screen

3300-003KJKABNF MVP Cartridge for 3300 Series Faucets

3300-103KJKABNF Actuator Assembly, Valve, Filter Screen for 3300 Series Faucets

Miscellaneous Cartridges

313-XJKABNF Glass Filler Cartridge

386-LEDXJKABNF Glass Filler Cartridge, Less Dashpot

386-XSLOJKNF Urinal Valve Cartridge

386-XSLOCJKNF Urinal Valve Cartridge With Handle and Button Assembly

745-XJKABNF Knee Valve Cartridge

KLO-SELF

™

Self-Closing Vandal Resistant Cartridge

Self-closing, closes upon release of the handle by the user

Product No. Description

825-XJKABNF For Concealed Cap Installations, Instant Closing

826-XJKABNF For Exposed Cap Installations, Instant Closing

826-XJKSPF For Concealed Cap Installations, Instant Closing, Silver Plate Finish

826-XJKTPF For Concealed Cap Installations, Instant Closing, Tin Plate Finish

KLO-SELF cartridges are interchangeable with right or left hand installation.

Product No. Description

217-XMLHJKABNF Exposed Cap, Left Hand, Short Stem, Metal to Metal

217-XMVCLHJKABNF Exposed Cap, Left Hand, Short Stem, Metal to Metal, Volume Control

217-XTLHJKABNF Exposed Cap, Left Hand, Short Stem

217-XTLHJKSPF Exposed Cap, Left Hand, Short Stem, Silver Plate Finish

217-XTLHJKTPF Exposed Cap, Left Hand, Short Stem, Tin Plate Finish

217-XTRHJKABNF Exposed Cap, Right Hand, Short Stem

217-XTRHJKSPF Exposed Cap, Right Hand, Short Stem, Silver Plate Finish

217-XTRHJKTPF Exposed Cap, Right Hand, Short Stem, Tin Plate Finish

274-XTLHJKABNF Concealed Cap, Left Hand, Long Stem

274-XTLHJKTPF Concealed Cap, Left Hand, Long Stem, Tin Plate Finish

274-XTRHJKABNF Concealed Cap, Right Hand, Long Stem

274-XTRHJKTPF Concealed Cap, Right Hand, Long Stem, Tin Plate Finish

376-CXJKABNF Slow Compression Cartridge with Integral Check Valve

828-111KJKNF Needle Point Cartridge for Lab Use, Polypropylene

870-110KJKPVC Needle Point Cartridge for Lab Use, Polyvinyl Chloride

937-XSTNF Steam Cartridge

962-XJKNF Needle Point Cartridge for Lab Use

962-XJKSAM Needle Point Cartridge for Lab Use, Satin Antimicrobial Finish

966-XJKNF Micro Needle Point/Brass Seat Cartridge for Lab Use

966-XSSJKNF Micro Needle Point/Stainless Steel Seat Cartridge for Lab Use

ECAST

Cartridges

How To Identify ECAST Cartridges

ECAST

, from Chicago Faucets, is the line of durable, high quality brass faucets and fittings that are designed and

manufactured with less than one quarter of one percent (0.25%) total lead content by weighted average. These products are

intended for installation in locations where federal law, state law, and local codes mandate lead content levels or wherever

lead content is a concern.

In order to maintain the low-lead characteristics and certified status of your existing ECAST installations, it is critical that you

identify and install the correct ECAST replacement parts. All replacement cartridges for ECAST products feature distinctive

markings to make them easy to identify on the job site.

Replacement cartridges for existing ECAST

installations feature two engraved rings around

the top of the cartridge sleeve.

Repair Kits

Repair Kit for Quaturn

™

and Slow Compression Operating Cartridges

One

Jiffy Minute Junior

Repair Repair Repair Description Part No.

Kit Kit Kit

1277-DAB 1273-ABNF 1276-ABNF

– 3 1 Left Hand Stem (HOT) –

– 3 1 Right Hand Stem (COLD) –

– 1 – Left Hand Long Stem –

– 1 – Right Hand Long Stem –

– 2 – Left Hand (HOT) Sleeves –

– 2 – Right Hand (COLD) Sleeves –

4 100 50 Seat Washers 1-021JKNABF

– 25 3 Washer Retainers 1-022JKABNF

– 12 6 Stem Nut Washers 1-031JKNF

2 – – Gasket 1-043JKABNF

– 4 1 Complete Right Hand (COLD) Cartridges 1-099XTJKABNF

– 4 1 Complete Left hand (HOT) Cartridges 1-100XTJKABNF

– 4 2 Chrome Plated Caps 1-214JKCP

2 24 9 O-Rings 1-219JKABNF

– 50 25 Seats 1-327JKABNF

2 24 25 O-Rings 1-328JKABNF

2 48 9 O-Ring 1-519JKABNF

2 24 6 Cap Thread Gaskets 2-043JKABNF

– 1 – Metal Box with Compartments 273-061JKNF

– – 1 Metal Box with Compartments 276-060JKNF

4 12 6 Stem Nuts 333-097JKABNF

– 1 – Complete Left Hand Long Stem Cartridge 377-XTLHJKABNF

– 1 – Complete Right Hand Long Stem Cartridge 377-XTRHJKABNF

– 6 – Handle Screws 420-010JKRCF

2 – – Brass Washers 93-031JKABRBF

2 24 9 Brass Washer 93-131JKABRBF

One

Jiffy Minute Junior

Repair Repair Repair Description Part No.

Kit Kit Kit

847-DAB 883-ABNF 884-ABNF

— 4 — Sleeves –

— 25 15 Washer Retainers 1-022JKABNF

2 50 25 Seats 1-027JKABNF

— 16 6 Stem Nut Washers 1-031JKABNF

— 20 6 Cap Thread Gaskets 1-043JKABNF

2 100 25 Soft Seat Washers 244-006JKABNF

– 1 – Metal Box with Compartments 273-061JKNF

– – 1 Metal Box with Compartments 276-060JKNF

2 8 2 Leather Packing 319-035JKABNF

4 16 4 O-Rings 319-140JKABNF

— 18 6 Stem Nuts 333-097JKABNF

— 25 6 Handle Screws 420-010JKRCF

— 6 2 Stems 585-001JKBNF

— 12 2 Packing Glands 711-007JKRBF

— 12 2 Plungers 823-001JKNF

— 6 2 Cap Nuts, Chrome Plated 823-004JKCP

2 18 2 Springs 823-010JKNF

— 12 2 Springs 823-013JKNF

2 20 6 O-Rings 823-015JKABNF

— 6 2 Bonnets 826-101JKRCF

Repair Kit for KLO-SELF

™

Type Cartridges

One

Jiffy Minute Junior

Repair Repair Repair Description Part No.

Kit Kit Kit

849-DAB 820-ABNF 821-ABNF

— 2 — Sleeves –

2 12 6 Seats 1-027JKABNF

— 6 3 Stem Nut Washers 1-031JKABNF

2 20 6 Cap Thread Gaskets 1-043JKABNF

2 50 25 Soft Seat Washers 244-006JKABNF

— 2 1 Pin Wrenches 244-025JKNF

– 1 – Metal Box with Compartments 273-061JKNF

– – 1 Metal Box with Compartments 276-060JKNF

— 12 6 Brass Washers 319-012JKRBF

2 7 3 Leather Packing 319-035JKABNF

4 14 6 O-Rings 319-140JKABNF

— 12 4 Washer Retainers 333-026JKABRBF

— 12 6 Guide Washers 333-039JKABNF

2 20 10 Cup Washers 333-040JKABNF

— 4 — Slow Dash Pot Assembly 333-073KJKABNF

— 4 2 Dashpot 333-075JKABNF

— 6 3 Stem Nuts 333-097JKABNF

— 4 2 Complete Naiad Cartridges 333-XPSHJKABNF

2 4 2 Springs 395-018JKNF

Repair Kits

Repair Kit for NAIAD

™

Push Button & Oscillating Handle Operating Cartridges

Part No. Description

665-190KJKABNF Actuator Assembly for Faucets with MVP Cartridge

667-080KJKABNF One Each of Kits 665-190KJKABNF and 671-XJKABNF

668-100KJKABNF (2) E Ring Retainer, Retainer Ring, Actuator O-Ring, Cartridge O-Ring,

Cap Sealing Washer, Large Filter and Small Filter

671-XJKABNF Metering Valve Unit

3300-003KJKABNF Actuator Assembly for 3300 Series Faucets

MVP

™

Repair Kits

(See illustration on page 6 for details)

The Chicago Faucet Company

2100 South Clearwater Drive

Des Plaines, IL 60018

Phone: 847/803-5000

Fax: 847/803-5454

Technical: 800/832-8783

www.chicagofaucets.com

CF1081 11/17

Chicago Faucets, a member of the Geberit Group, is the leading brand of commercial faucets and fittings in the United States,

offering a complete range of products for schools, laboratories, hospitals, office buildings, food service, airports, and sports

facilities. Whatever your requirements may be, Chicago Faucets offers standard and made-to-order products that are designed

to meet any commercial application.

We are a member of the U.S. Green Building Council and support the

Leadership in Energy and Environmental Design (LEED) Green Building

Rating System

™

, to measure the efficiency and sustainability of buildings

in the U.S. and Canada. If you are trying to achieve LEED Certification

for your building, our low-flow outlets, metering cartridges, and sensor-

operated faucets can contribute points in these areas: Water Efficiency

Credit 2: Innovative Wastewater Technologies and Water Efficiency

Credit 3: Water Use Reduction.

We are proud to be a partner with WaterSense

, sponsored by the

EPA and designed to protect the future of our nation’s water supply

by promoting efficiency and enhancing the market for water efficient

products, programs, and practices.

We are a charter sponsor of the Alliance for Water Efficiency, a non-

profit organization that is dedicated to the efficient and sustainable use

of water. It brings together a diverse range of stakeholders to advocate

water efficiency and conservation.